TYRE INFLATION SYSTEM

ACCESSORIES

Compressed air is an energy carrier and you want to use this energy in the right place. It is therefore important that you do not lose that energy during transport to pressure loss and leakage. Therefore, use large pipes and openings in your components, keep distances as short as possible and avoid (sharp) bends to prevent pressure losses. Prevent leaks and remove dirt, oil and condensation from your compressed air.

ACCESSORIES

Compressed air is an energy carrier and you want to use this energy in the right place. It is therefore important that you do not lose that energy during transport to pressure loss and leakage. Therefore, use large pipes and openings in your components, keep distances as short as possible and avoid (sharp) bends to prevent pressure losses. Prevent leaks and remove dirt, oil and condensation from your compressed air.

Fittings
QTIS recommends brake fittings with O-ring seals and a long, stable tubing holder that inextricably connects the PA12 brake line for reliable, fast and safe installation.
Article number Description Downloads
QTIS-PF06-12-180 BRAKE FITTING STRAIGHT 6MM x G1/2 *on request
QTIS-PF16-12-180 BRAKE FITTING STRAIGHT 16MM x G1/2 *on request
QTIS-PF16-22-180 BRAKE FITTING STRAIGHT 16MM x M22x1,5 *on request
QTIS-PF16-26-180 BRAKE FITTING STRAIGHT 16MM x M26x1,5 *on request
QTIS-T12-12SW12 T FITTING FFM G1/2-G1/2-SW G1/2 *on request
QTIS-PF16-1290LL BRAKE FITTING 90° 16MM x G1/2 HIGH *on request
QTIS-PF16-12-90 KE FITTING 90° 16MM x G1/2 *on request
QTIS-PF16-22-90 BRAKE FITTING 90° 16MM x M22x1,5 *on request
QTIS-PF12-26-90 BRAKE FITTING 90° 16MM x M26x1,5 *on request
QTIS-TA16-06-12 T ASSEMBLY 16MM - 06MM -G1/2 SWIVEL *on request
QTIS-SW12-12 G1/2 x G1/2 SWIVEL NUT *on request
Compressed air transport pipes
QTIS structurally uses automotive-grade PA12-PHLY pipes from European raw material suppliers and manufacturers, in order to guarantee the required quality standards of ISO7628, DIN73378 and DIN74324.  We recommend using the 16×2 mm pipe throughout the system, and not smaller diameters.
Article number Afmetingen (mm) Minimale buigradius Barstdruk (BP) @ 23°C
QTIS-PA12-12X1.5 Ø12 x 1,5 (Ø12 x Ø9) 80 mm >25 bar / 2,5 Mpa
QTIS-PA12-16X2 Ø16 x 2 (Ø16 x Ø12) 105 mm >25 bar / 2,5 Mpa
Filters and condensate separators

Filters keep the compressed air clean, just as you would use filters for hydraulic oil. They are essential for protecting the compressor and various valves from dirt and moisture in the system. The recommended filtration level is 50 µm (micron). A cyclone filter ensures that condensate is spun against the inner wall of the filter housing and collected at the bottom, where it can be drained off via a float valve. Contact us for advice on the most suitable system configuration.

Article number Description Downloads
QTIS-CYCLF-112 CYCLONE FILTER 5100 L/M G1.1/2 *on request
QTIS-CYCLF-34 CYCLONE FILTER 2800 L/M G3/4 *on request
QTIS-MDFP1050 MEMBRANE FILTER 1050 NL/MIN G1/2 *on request
QTIS-MDFP2050 MEMBRANE FILTER 2050 NL/MIN G1/2 *on request
QTIS-MDFP3000 MEMBRANE FILTER 3000 NL/MIN G1 *on request
QTIS-NA-AFD CONDENSATE DRAIN G1/2 *on request
Cables & Connectors

To minimise assembly time and reduce wiring complexity, QTIS offers the QTIS-M12-5DIN cable set. This consists of a single 25 cm cable with an M12 connector and a split to 5 DIN connectors, for controlling the 4 directional control valves and the double-pressure valve on the valve manifold. Also available in a version for 6 directional control valves. Can be expanded with M12 extension cables if required.

Article number Description Downloads
QTIS-M12-5DIN M12-8PIN CONNECTOR TO 5 DIN CONNECT *on request
QTIS-M12-7DIN M12-8PIN CONNECTOR TO 7 DIN CONNECT *on request
QTIS-MF-M12-2000 CABLE 2000MM M12-8PIN-MALE-FEMALE *on request
QTIS-MF-M12-3000 CABLE 3000MM M12-8PIN-MALE-FEMALE *on request
QTIS-MF-M12-4000 CABLE 4000MM M12-8PIN-MALE-FEMALE *on request